Митрофан Posted April 7, 2010 Report Share Posted April 7, 2010 Вот мне всё написали: Микросхема прошиваемая, Winbond W39F010P. Хотя, бывает, что ST-Lab блокирует флешки на перезапись, но будем надеяться на лучшее. А теперь качайте http://www.siliconimage.com/docs/SiFlashTool.zip - утилита прошивки для винды и http://www.siliconimage.com/docs/SiI3114_5500.zip - биос для контроллера. Как прошить - несложно догадаться Перед прошивкой обязательно подключите к контроллеру какой-нибудь диск. Вот этот драйвер http://www.siliconimage.com/docs/SiI3114_x...3.11.0_logo.zip должен подойти для этого биоса. .....и испарились. А дисковод не пашет. Через CD-RW можно!? А КАК!? В ЛайфСиДи грузиться и там запускать екзешник ? Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 7, 2010 Author Report Share Posted April 7, 2010 Сказали мне прошивать надо тока с подключенным хардом. А в этом случае винда не грузится. Дальше БИОСа контроллера комп не грузится. ЧТО ДЕЛАТЬ!? Подключить хард после БИОСА!? Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 7, 2010 Author Report Share Posted April 7, 2010 Может перевести хард в режим SATA I!? А как это сделать!? Quote Link to comment Share on other sites More sharing options...
Roader Posted April 8, 2010 Report Share Posted April 8, 2010 Может перевести хард в режим SATA I!? А как это сделать!? Перемычкой, которая может устанавливаться возле SATA интерфейса на харде, если он таковой режим предусматривает. Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 8, 2010 Author Report Share Posted April 8, 2010 Перемычкой, которая может устанавливаться возле SATA интерфейса на харде, если он таковой режим предусматривает. На Сигейте не узрю такую. Ещё есть Хитачи и Самсунг по 1 тб.... Прежде чем выковыривать их, на каком из них можно SATA 1 поставить!? Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 8, 2010 Author Report Share Posted April 8, 2010 КАК там надо джампер переставить!? Хэлп! Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 8, 2010 Author Report Share Posted April 8, 2010 Джампер не поможет.... А такой вариант - подключить хард после БИОСА контроллера!? Quote Link to comment Share on other sites More sharing options...
Roader Posted April 9, 2010 Report Share Posted April 9, 2010 (edited) КАК там надо джампер переставить!? Хэлп! В режим 1.5 Gbit/s Джампер не поможет.... А такой вариант - подключить хард после БИОСА контроллера!? Можно. А вообще, загрузка BIOS тормозиться на детектировании харди им, правильно я понял? Вам точно ответели что проблема в старой прошивке? Другой жёсткий пробовали подключать (на 120...300 GB)? На другой материнке контроллер проверяли? Edited April 9, 2010 by Roader Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 9, 2010 Author Report Share Posted April 9, 2010 В режим 1.5 Gbit/s Можно. А вообще, загрузка BIOS тормозиться на детектировании харди им, правильно я понял? Вам точно ответели что проблема в старой прошивке? Другой жёсткий пробовали подключать (на 120...300 GB)? На другой материнке контроллер проверяли? Проблема точно в старой прошифке. Теперь не могу запустить прошивальщик в винде - мелькнёт на мгновение досовское окно и исчезнет. Вот инструкция к нему:[more] Instructions for Using Windows SiFlashTool BIOS Update Utility 10/4/2006 updated The SiFlashTool.exe Windows command prompt utility can be used to load BIOS, BOOT ROM code to the flash memory hosted by a Silicon Image SATA or PATA controller. The SiFlashTool.exe supports the following Silicon Image, Inc. controllers. SiI 0680 SiI 3x12 SiI 3114 SiI 3124 SiI 3132 SiFlashTool .exe supports the following flash memory chips: • AMD Am29F010B • AMD Am29LV010B • AMD Am29LV040B • AMD Am29LV400BB • AMD Am29LV400BT • Atmel AT29LV010A • Atmel AT49BV512 • Macronix • MX29LV004B • Macronix MX29LV004T • Macronix MX29LV040 • Macronix MX29LV400B • Macronix MX29LV400T • Sanyo LE28C1001D • SST 39SF010 • SST 39SF020 • SST 39VF010 • SST 39VF020 • ST Micro M29F010B • ST Micro M29W040B • ST Micro M29W400DB • ST Micro M29W400DT • Winbond W29C011A • Winbond W29EE512 Procedures to run SiFlashTool .exe • Open Windows command prompt • Change to a directory where the SiFlashTool .exe and BIOS binary file are located. • Run SiFlashTool to update the flash memory with BIOS binary code The SiFlashTool.exe command line syntax is as follows: SiFlashTool [/busNum:xx /DevNum:xx] [/File:filespec] [/v] Where: BusNum / DevNum: These parameters specify the PCI bus and device number respectively of a Silicon Image storage controller. These parameters only need to be used if there is more than one Silicon Image storage controller in the system. File: This parameter specifies the path and name of the BIOS image file to be programmed. /V: This switch causes the program to only display the version number of a controller's BIOS. No BIOS image is programmed when this switch is used. The /File parameter is ignored if specified along with this switch. If /BusNum and/or /Devnum are specified, then only the BIOS versions of controller's at the specified PCI locations are displayed. The following list identifies SiFlashTool.exe return codes noted when the program exits. • 0 – BIOS update succeeded. SiFlashTool successfully confirmed a match between the bin file and resulting FLASH contents. • 1 – Invalid parameter value specified. • 2 – Unrecognized parameter specified. • 3 – SiFlashTool does not support the implemented FLASH chip. • 4 – Silicon Image controller not found. • 5 – BIOS image file was not found. • 6 – Error encountered while reading the BIOS image file. • 7 – Image file is too large for the implemented FLASH ship. Download was aborted. • 8 – Failed to perform FLASH chip erase before writing the BIOS to the FLASH chip. • 9 – Failed to perform a FLASH chip write. • 10 – After writing BIOS to the FLASH chip, failed to verify FLASH chip contents to the BIN file. • 11 – Incorrect controller selected [/more] Английского не изучал и чего там не пойму...... Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 10, 2010 Author Report Share Posted April 10, 2010 Проблема. Запускаю екзешник прошивальщика, а мне выдается это окно: Почему!? КАК прошить-то!? Quote Link to comment Share on other sites More sharing options...
Roader Posted April 10, 2010 Report Share Posted April 10, 2010 А какое имя файла, который вы запускаете? Почему он так странно отображается в командной строке? Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 10, 2010 Author Report Share Posted April 10, 2010 А какое имя файла, который вы запускаете? Почему он так странно отображается в командной строке? Запустилось так: Нажал пробел и окно свернулось, прошилось или нет, не знаю, но ничего не изменилось. БИОС контроллера НЕ ПУСКАЕТ ком грузиться дальше;)((. Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 10, 2010 Author Report Share Posted April 10, 2010 Мне выдали такой эпикриз: Не прошился у вас BIOS. Утилита отругалась. Похоже требует чёткого указания устройства по шине. .... незнаю как вам помочь. Был бы девайс на руках, сделал бы, а прошивать ТАК в режиме "ремоут монк", это угробить девайс. Может кто другой чего посоветует. А кто этот - другой!? Софтбоард!:) Хэлп ми! Quote Link to comment Share on other sites More sharing options...
Roader Posted April 10, 2010 Report Share Posted April 10, 2010 А только с ключём /V пробовали запускать? Заскринте результат, что отобразиться в командной строке. Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 11, 2010 Author Report Share Posted April 11, 2010 с ключём /V А как!*? Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 11, 2010 Author Report Share Posted April 11, 2010 В свой БИОС контроллер не пускает:). Ctrl+S или F4 - неработают........ Почему!? Странный он какой-то..... Мож разрабы так шутят? Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 11, 2010 Author Report Share Posted April 11, 2010 Урррря, товарищи, прошилось наконец! Quote Link to comment Share on other sites More sharing options...
Roader Posted April 11, 2010 Report Share Posted April 11, 2010 Пршился это хорошо, но вы не сообщили о самом главном: Теперь всё заработало? Не спупориться на нём при загрузке? Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 12, 2010 Author Report Share Posted April 12, 2010 Пршился это хорошо, но вы не сообщили о самом главном: Теперь всё заработало? Не спупориться на нём при загрузке? Да всё бы хорошо, но хард Сасунг, 1 тб теперь определяется, как 32 мб. Полгода назад такое с ним было, мамка Гигабайтная глючит так. Мне недавно всё починили и маму прошил. А вот снова........ Контр виноват!? Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 12, 2010 Author Report Share Posted April 12, 2010 К маме подключу. ТЬФУ-тьфу! Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 12, 2010 Author Report Share Posted April 12, 2010 С мамой дело намного получше! Не 32 мб, а целых 7.8 гб! Quote Link to comment Share on other sites More sharing options...
Roader Posted April 12, 2010 Report Share Posted April 12, 2010 Митрофан, напишите модель материнки. Кстати, 0-вой диск на терабайт она видит нормально (скрин). Quote Link to comment Share on other sites More sharing options...
Митрофан Posted April 13, 2010 Author Report Share Posted April 13, 2010 Митрофан, напишите модель материнки. Кстати, 0-вой диск на терабайт она видит нормально (скрин). Мамка Гигабайтная, и этот её глюк известен. А хард я мастеру отнёс, теперь это его вотчина. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.